Does pooled freight volume mean giving up our own carrier contracts?
Does pooled freight volume mean giving up your own carrier contracts?
A distributor of commercial plumbing supplies ships from two warehouses. It has a signed agreement with one regional LTL carrier that covers most of its outbound pallets, a second LTL carrier as backup, and a truckload carrier that runs a weekly replenishment lane between the warehouses. That accounts for roughly 70% of its loads. The other 30% is everything else: a flatbed to a job site, a one-off truckload to a new customer three states away, a few LTL shipments a month into a region the contract carrier doesn't serve well. Those loads are quoted by email, one at a time, and the rates are whatever comes back that afternoon.
When the logistics manager hears that a network can bring better rates because many shippers' volume counts together, the first question is the obvious one: does that mean walking away from the carriers it spent two years negotiating with?
No. Pooled freight volume is a second source of rates that sits next to your own contracts, not a substitute for them. You keep your carriers, your contracts and your rates. On the lanes where your contract carrier is the best option, it stays the best option. On the lanes where you ship too little to earn a good rate on your own, pooled volume gives carriers a reason to price your freight as part of a larger, steadier flow. The decision is made lane by lane, and the company still approves every carrier that hauls its freight.
What "pooled volume" means in plain terms
A carrier prices a lane on how often it can expect freight there, how well that freight fits its network and how much empty driving it saves. One shipper sending four loads a month on a lane is a small, irregular customer. Twenty shippers whose combined freight puts sixty loads a month on the same lane and equipment type are a reason to place trucks there. Pooling means the carrier sees the combined flow when it prices each load, even though each load still belongs to one shipper, moves under that shipper's references and is billed against that shipper's booking.
Pooling does not mean your freight is consolidated onto someone else's truck, that your customer data is shared with other shippers, or that you give up the right to choose carriers. It is about rates and capacity, not about who owns the shipment.
The short answer by situation
| Your situation | What pooled volume changes | What stays the same |
|---|---|---|
| Signed contract with committed volume on a lane | Nothing on that lane unless the contract allows it | The contract carrier, rate, tender rules and commitment |
| Contract rate on a lane, no volume commitment | You can compare network quotes against the contract rate | The contract carrier remains an approved option |
| Spot-only lanes with no regular carrier | Network quotes add carriers and brokers to compare | Your approval of each carrier before it hauls |
| Thin lanes your contract carrier serves poorly | Network capacity can cover them | Your contract carrier on its strong lanes |
| A broker handles everything today | You can book lanes yourself and keep the broker as an option | Your choice of which lanes move first |
Let's review which lanes could use network rates and which stay with your carriers. You don't need to prepare anything: Cartage maps the workflow with you on the call.
See it on your own loads. Wilson, by Cartage, is an AI logistics agent that quotes, books, tracks, audits and pays for freight with your approved carriers.
Book a demo →How do pooled network rates actually work?
Carriers price lanes on density and fit, so a network that brings many shippers' loads to the same lane and equipment type gives carriers a steadier flow to price against. The rate on any single load still depends on the shipment, the date and the market, but the carrier is no longer pricing an isolated request from an unknown shipper.
Why one shipper's volume often isn't enough
A carrier's cost on a load is mostly the truck, the driver and the miles. The part of the cost it can control is how much of that time is spent loaded. A lane where the carrier can count on freight both ways, or on a reload near the delivery point, costs it less to run than a lane where the truck drives back empty. That's why a shipper with steady freight on a lane gets a better rate than a shipper who appears twice a quarter.
What changes when volume is combined
When a network combines the freight of many shippers, a lane that was four loads a month for one shipper can be dozens of loads a month for the carriers serving the network. Each shipper's load is still tendered, tracked and paid as its own shipment. What changes is the carrier's view of the lane: it is pricing part of a flow it can plan around.
The benefit is uneven, and it should be. Lanes where many shippers move similar freight on similar equipment benefit most. A lane only one shipper runs, with unusual equipment or tight appointment rules, benefits less. Nobody can promise a fixed percentage saving across all freight, and a shipper should be wary of anyone who does.
Carriers and brokers on the same network
A network can include both asset carriers and freight brokers. A broker on the network is useful when it has capacity on a lane that no asset carrier on the network covers well, or when the load needs a carrier the broker already manages. The shipper should still see who quoted, who was picked and why, and the broker still needs the shipper's approval before it is used.
What pooled volume does not do
- It does not lock in a rate. Network quotes are quotes for a load or a period, not a contract. Contract rates you have negotiated remain your fixed reference.
- It does not remove the market. If capacity tightens across the country, network rates rise too. Pooling improves your position on a lane; it doesn't cancel supply and demand.
- It does not replace your approval. A carrier on the network is not automatically approved to haul your freight.
- It does not move ownership of your records. Your loads, rates, documents and contacts stay yours, whichever carrier hauls them.
A worked example
Take a hypothetical dry van lane from a warehouse in Indiana to a customer in Georgia. The shipper sends three or four loads a month. Today it emails four carriers for each load and books the lowest answer. Some weeks two of them don't reply.
With a network in the mix, the same load is quoted by the shipper's own approved carriers and by approved carriers and brokers on the network that run the lane for other shippers. The coordinator, or the agent working for the coordinator, compares every quote on total cost, including fuel and the accessorials the load needs. If a network carrier's all-in price is lower and that carrier is approved, it books. If the shipper's own carrier wins, it books. The lane gets more competing quotes per load without the shipper giving up any of its existing carriers.
The article on lane rate benchmarking covers how to tell whether a lane's rate is in line with the market before deciding which lanes to test.
Which lanes should stay with your contract carriers, and which can use network rates?
Keep a lane with your contract carrier when the carrier performs, the rate is competitive and the contract or relationship depends on the volume. Open a lane to network rates when your volume is too thin to earn a good rate, when you are buying it on the spot market anyway, or when your carrier serves it poorly. Decide lane by lane, write the decision down, and revisit it on a schedule.
Start with a lane inventory
Pull three to six months of loads and group them by origin region, destination region, mode and equipment. For each lane, record:
- Loads per month and how steady that number is.
- Who hauled them, and whether that carrier is under contract.
- The rate paid, all-in, including fuel and accessorials.
- Whether the contract includes a volume commitment, a first-look promise or a minimum tender share.
- Service on the lane: tender acceptance, on-time pickup, on-time delivery and claims.
- How the load was bought: contract rate, spot quote, or a broker.
Most shippers find the same pattern. A handful of lanes carry most of the volume and are already under contract. A long tail of lanes each carries a few loads and is bought on the spot.
A lane decision table
| Lane profile | Typical decision | Why |
|---|---|---|
| High volume, contract rate, strong service, volume commitment | Keep with contract carrier | The commitment and the service are worth protecting |
| High volume, contract rate, strong service, no commitment | Keep, and compare network quotes periodically | Confirms the contract rate is still competitive |
| High volume, contract carrier often rejects tenders | Keep contract carrier first, network as backup | Rejected tenders are already going to the spot market |
| Medium volume, bought on the spot | Open to network rates | Pooled volume can help where yours alone doesn't |
| Low volume, irregular, no regular carrier | Open to network rates | This is where one shipper has the least leverage |
| Unusual equipment, strict appointment rules, high-value freight | Keep with proven carriers, add network carriers only after approval | Service risk outweighs the rate difference |
| Lane served by a broker today | Decide per lane; the broker can stay an approved option | Moving it is a choice, not a requirement |
Don't move a lane just because a quote is lower
A lower quote on one load is not a reason to move a lane. Your contract carrier may be the one that answers the phone at 6 a.m. when a load goes wrong, or the one that takes your Friday afternoon freight when nobody else will. A lane decision should weigh the rate, the service record and the relationship.
A useful rule: if the contract carrier is within a tolerance you set (for example, within a few percent of the best approved network quote on total cost) and its service is good, the contract carrier keeps the load. If the gap is larger, someone reviews it before the lane changes. That keeps the decision in the hands of the logistics team rather than letting each load drift to whoever was cheapest that day.
What happens to your contract terms, commitments and routing guide?
Your contract terms stay in force, and the safest way to honor them is to turn each term into a booking rule that applies before any network quote is considered. The risk with pooled rates isn't that the contract disappears; it's that loads drift away from a committed carrier one at a time, and nobody notices until renewal.
Terms that should become rules
| Contract term | What it means in practice | The booking rule |
|---|---|---|
| Volume commitment | You promised a number of loads or a share of a lane | Tender the committed share to the contract carrier first and track the count |
| First look or right of first refusal | The carrier sees the load before anyone else | Tender to the contract carrier first and wait its response window before quoting elsewhere |
| Tender response window | The carrier has a set time to accept | Move to the next option only after the window closes |
| Accessorial schedule | Agreed charges for liftgate, detention, appointment | Audit invoices against the schedule, not against the market |
| Fuel surcharge table | Fuel moves with a published index | Apply the table to compare contract and network quotes fairly |
| Rate validity | The contract rate runs to a date | Flag lanes before expiry and compare network quotes ahead of renewal |
| Exclusivity on a lane | Only that carrier may haul it | No network quotes requested for that lane |
The routing guide still decides the order
A routing guide lists which carrier gets each lane, in what order. Pooled rates don't replace it; they add steps to it. A simple version for a lane with a contract carrier and no commitment: tender to the contract carrier first; if it rejects or doesn't respond inside the window, request quotes from the backup carrier and approved network carriers; book the best approved option on total cost.
For a lane without a contract carrier, the routing guide can open straight to quotes: request quotes from your own approved carriers and from approved network carriers and brokers at the same time, compare on total cost and book.
Watch the commitment count
If you promised a carrier 80% of a lane, someone has to count. A spreadsheet that gets updated at month-end is how commitments get missed. The count should be kept on the record with each load, so that before a load on that lane goes to anyone else, the share is checked.
Read the contract before you test
Some carrier agreements say nothing about how much freight you send elsewhere. Others include minimums, exclusivity or penalties. Read yours before you open a lane to network quotes. The specific wording matters more than general industry practice. When in doubt, ask the carrier: most would rather discuss a change than find out at renewal that their volume dropped.
The articles on preserving direct carrier contracts in carrier management software and on spot quotes vs. contract rates cover the contract side in more detail.
Who approves the carriers when the network is in the mix?
The shipper does, for every carrier, whether it came from the shipper's own list, from the network or through a broker on the network. Pooled rates widen the set of carriers that can quote. They should never widen the set of carriers that can haul without the company's say.
What approval should include
- Identity and authority: the carrier's USDOT and MC numbers, operating authority and the correct company details.
- Insurance: current certificates with the limits your freight needs.
- Scope: which modes, lanes, equipment and freight the carrier may haul. A carrier approved for dry van LTL in the Midwest is not automatically approved for reefer truckload to the Southeast.
- Limits: the maximum rate or freight value it can be booked for without a further approval.
- Who approved it and when, kept on the carrier's record.
The guide to checking a new carrier before the first load walks through these checks in order, and the article on keeping approved carriers approved when booking becomes automated covers how scope and suspensions should work once software is booking.
How network carriers get into your approved set
A practical sequence:
- Cartage suggests additional carrier capacity, carriers or brokers, for your lanes.
- Your team reviews each one against your approval criteria.
- Approved carriers are added with a scope: specific lanes, modes or equipment.
- Network quotes are only requested from, and only booked with, carriers inside that scope.
- Carriers that fail on service are suspended or removed, and the change is recorded.
Some shippers approve a short list of network carriers per lane at the start and add more as volume grows. Others approve broadly for low-risk freight and narrowly for high-value or time-critical loads. Both work, as long as the rule is written and the booking follows it.
How does Wilson, by Cartage, handle network rates and your own carriers side by side?
Wilson, by Cartage, is an AI logistics agent that requests quotes from the company's own approved carriers and from Wilson's network at the same time, follows the company's contract rules and routing order, compares every option on total cost and books only carriers the company has approved. Traditional logistics software gives teams information. Wilson executes the work required to move shipments forward.
Wilson works as a free logistics department for manufacturers and distributors: what big shippers build over years, Wilson does from day one. Wilson quotes, books and tracks freight, and pays carriers. Each of the four parts of that department matters when network rates and contracts run together.
The labor
The labor is the work of running the routing guide on every load. Wilson reads each order, checks the lane's rules, tenders to the contract carrier first where the contract says so, waits the response window, and only then requests quotes from backup carriers and the network. It follows up with carriers by email, phone calls where configured, and the channels the team already uses, and it negotiates toward the company's rate targets within approval limits. From the first quote to the final POD it handles the bookings, paperwork, tracking and carrier follow-ups. The team doesn't chase carriers.
The data
The data is where the split between network and contract freight stays visible. Wilson keeps every order, load, quote, rate, document and contact on record as it works, connected to the company's ERP. Each load keeps the quotes requested, the carrier booked and the rate confirmation. That makes commitment counts and contract-versus-network comparisons a matter of reading the record rather than rebuilding a spreadsheet. Wilson also keeps rules and memories, learned from its own work or added by the team, such as "the contract carrier gets first look on this lane" or "this customer only takes deliveries before noon", and the team can edit them. Wilson replaces the TMS for freight execution and connects to the company's ERP. Wilson works with SAP, NetSuite, Microsoft Dynamics 365, Oracle, Infor, Epicor, Sage, Acumatica and other ERP environments, with the exact connection depending on the customer's data flow and scope. The company owns its carriers, rules and contacts, and the records are searchable and exportable with change history.
The network
The network is where pooled volume comes in. The shipper's volume counts with every other Wilson customer's, which can bring better freight rates on its lanes. The network includes carriers and brokers. Shippers can keep their own carriers on any lane, and Wilson can produce lane-rate reports on request from the loads it runs, so the comparison is visible. The company still approves who hauls its freight.
The payments
The payments treat both kinds of freight the same way. Wilson audits every freight invoice against the load, the rate confirmation and the POD before money moves, and pays carriers from the Wilson Wallet, whether the carrier came from the network or the shipper's own list. When an invoice is over the rate, Wilson asks the carrier why before paying, and invoices over the rate or outside the rules wait for a person.
Pricing
Wilson is free on Wilson's network: the shipper pays the freight rate and nothing on top. When a shipper keeps its own carriers, the fee is 2% to 0.5% of what Wilson pays them, falling with volume. There are no seat fees, no setup cost and no contract.
A hypothetical month makes the difference concrete:
| Freight in the month | Who hauls it | Freight paid | Wilson fee |
|---|---|---|---|
| Contract LTL lanes | Shipper's own carriers | $140,000 | At 2%: $2,800 |
| Replenishment truckload lane | Shipper's own carrier | $40,000 | At 2%: $800 |
| Tail lanes opened to network rates | Approved carriers and brokers on Wilson's network | $60,000 | $0 |
The fee on the shipper's own carriers falls toward 0.5% as volume grows; the exact rate depends on the shipper's volume. The network loads carry no fee on top of the freight rate. Whether network rates are lower than what the shipper paid on those tail lanes before is something to measure lane by lane, not assume.
When Wilson acts and when a person steps in
| Situation | What Wilson does | When a person steps in |
|---|---|---|
| Load on a lane with a volume commitment | Tenders to the contract carrier first and keeps the load on the record for the commitment count | When the contract carrier rejects and the share is at risk |
| Load on a lane with no contract carrier | Requests quotes from own approved carriers and the network, compares on total cost | When the best option is outside the approval limits |
| Network quote beats the contract rate by more than the set tolerance | Books the contract carrier if rules say so, and records the gap | When the team decides whether the lane should change |
| Cartage suggests a carrier not yet approved | Doesn't book it | The team reviews and approves, or declines |
| Invoice from a contract carrier | Audits against the contract rate and accessorial schedule | When a charge is over the rate or outside the rules |
Wilson starts with assisted execution. The company sets approval limits, and routine actions can run automatically within those rules as the workflow is proven. It handles LTL, FTL, ocean, drayage, parcel and cross-border freight. It is not a freight broker or a customs broker. Timing depends on scope: most teams start on a few lanes and expand from there.
FAQs
If we use Wilson's network, do we keep our own carriers?
Yes. Wilson, by Cartage, an AI logistics agent, works with the shipper's own carriers, contracts and rates and with carriers and brokers on Wilson's network. The shipper decides which lanes stay with its carriers and which open to network quotes, and still approves every carrier before Wilson books it. Network loads are free; loads on the shipper's own carriers carry a fee of 2% to 0.5% of what Wilson pays them.
What is pooled freight volume?
Pooled freight volume is the combined freight of many shippers on the same lanes and equipment, presented to carriers as a steadier flow than any one shipper's loads. Each load still belongs to one shipper. Carriers can price that flow better than isolated spot requests.
Will moving some loads to a network break our carrier contract?
It depends on the contract. Agreements with volume commitments, exclusivity or first-look terms limit what can move. Read the terms, turn them into booking rules and keep committed lanes with the contract carrier. Lanes without commitments can be compared against network quotes.
Which lanes benefit most from network rates?
Low-volume, irregular and spot-heavy lanes usually benefit most, because one shipper's freight there is too thin to earn a good rate on its own. High-volume lanes with good contracts and service usually stay with the contract carrier.
Does a network carrier need our approval before it hauls our freight?
It should. A carrier on a network is not automatically approved to haul your freight. Check its authority, insurance and scope the same way you would any new carrier, and record who approved it.
How do we keep track of a volume commitment?
Count every load on the committed lane against the share promised, on the load record rather than in a month-end spreadsheet. Check the count before any load on that lane goes to another carrier, so the commitment is not missed one load at a time.
Is a network the same as using a freight broker?
No. A broker typically takes over the carrier relationship and the load. With a network, the shipper keeps its own carriers, approves the network carriers and brokers it uses, and keeps the record of every load. Wilson is not a freight broker.
How do we compare a network quote with our contract rate?
Compare on total cost: base rate, fuel at the same index and the accessorials the load needs. A network quote that looks lower on base rate can cost more once a liftgate or appointment is added.
Sources
- Cartage, Wilson product FAQ and product scope, October 2026: https://cartage.ai
- Cartage, Wilson network page, November 2026: https://cartage.ai/network
Let's review which lanes could use network rates and which stay with your carriers. You don't need to prepare anything: Cartage maps the workflow with you on the call.
