The reefer load arrived out of temperature. What now?
The reefer load arrived out of temperature. What now?
It is 6:20 a.m. at a customer's distribution center. A refrigerated truckload of fresh dairy has just been opened. The bill of lading says "Maintain 36°F, continuous." The receiver probes the rear pallets and gets 44°F. The front pallets read 37°F. The receiver calls the shipper's customer service line and asks whether to take the load. The driver wants to know if he can leave. The shipper's logistics coordinator is still on her way to work.
When a reefer load arrives out of temperature, the first job is to protect the product and the evidence: probe and photograph, set the product aside, keep the trailer and the driver long enough to record the unit's readings and decide with the receiver and the quality owner whether to accept, partly accept or reject. After that comes the claim, then the root cause. Doing them in that order keeps the claim strong and the next load safe.
The temptation is to rush to a verdict on the dock. The receiver wants to clear the door, the driver wants to leave and everyone wants to know who pays. But the decisions made in the first hour shape everything after. A rejected load with no product temperatures recorded is a weak claim. An accepted load with a clean signature and no notes may be no claim at all.
What "out of temperature" actually means
Out of temperature is not one condition. It can mean the trailer's air was out of range at arrival but the product was still fine. It can mean the product itself was warm, which matters far more. It can mean one zone of the trailer failed while the rest held. Each one leads to a different decision, which is why product temperatures, taken at several points in the load, matter more than the number on the unit display.
The first hour on the dock
The receiver, guided by the shipper, should:
- Probe product at several points: front, middle and rear of the trailer, top and bottom of pallets. Record each reading with the pallet and position.
- Photograph everything: the unit display showing setpoint and return air, the product probes, the pallet positions and any visible damage or condensation.
- Note it on the delivery receipt before signing. "Rear 6 pallets probed 43–45°F; front 14 pallets 36–38°F" is a strong note. A clean signature with no exception is a weak start for any claim.
- Set the product aside in a cold area, separated from accepted stock, until the decision is made.
- Ask the driver for the unit's temperature record for the trip, or at least a photo of the unit's settings and recent history if the display shows it.
Who decides acceptance
The receiver decides whether its dock accepts the freight. The shipper, as the owner of the product until delivery under most terms, should have a say, and the person responsible for product quality should make the call on safety. Agree in advance who that person is and how the receiver reaches them at 6 a.m. The guide on shipping temperature-controlled freight covers how to set those rules before the season starts.
Want to see how your team would handle it today?
Let's review how your team handles a temperature claim today. You don't need to prepare anything: Cartage maps the workflow with you on the call.
See it on your own loads. Wilson, by Cartage, is an AI logistics agent that quotes, books, tracks, audits and pays for freight with your approved carriers.
Book a demo →What should happen in the first day, step by step?
In the first day, the team should decide the product's fate, notify the carrier in writing, request the carrier's temperature records, arrange replacement product for the customer and open the claim file. Each step has a deadline that is easier to meet the same day than a week later.
Step 1: Decide accept, partial accept or reject
Use the product's temperature limits, not only the setpoint. A product that must stay at or below 41°F and probes at 44°F is a different case from one probing at 38°F with a setpoint of 36°F. Partial acceptance is common: the front pallets are in range and are received, the rear pallets are rejected. Record exactly which pallets were accepted and which were not, by count and position.
Step 2: Notify the carrier in writing
Send the carrier a short written notice the same day: load reference, delivery date, what was found, which pallets are affected and that the shipper intends to file a claim. Ask the carrier to hold its equipment records and say whether it wants to inspect the product. This notice is not the claim itself, but it starts the record and gives the carrier the chance to inspect.
Step 3: Request the carrier's temperature records
Ask for the reefer unit's download for the whole trip, showing setpoint, mode, return and discharge air, and any alarms or shutdowns. Under the federal sanitary transportation rule for food, a carrier that has agreed in writing to be responsible for temperature control must, if the shipper or receiver asks, show that it maintained temperatures consistent with the operating temperature the shipper specified. The rule lets the parties agree on how, such as temperature readings at loading and unloading or time and temperature data for the trip.
Step 4: Decide what happens to rejected product
Rejected product has three common paths: return to the shipper, transfer to another location for inspection or salvage, or disposal. The carrier may have rights to inspect or salvage before disposal, so ask before destroying anything. The article on whether to replace damaged product or ship it back walks through that cost comparison. For refused freight more generally, see what to do when a customer refuses a delivery.
Step 5: Take care of the customer
The customer still needs product. Decide whether to ship a replacement, from where and how fast. A replacement shipped the same afternoon may need a different carrier and a premium rate. Record the replacement cost on the original load: it may form part of the claim, depending on the terms and the facts.
Step 6: Open the claim file
Collect everything on one shipment record: the BOL, the rate confirmation, the loading records, the delivery receipt with notes, the photos, the probe readings, the carrier's notice, the carrier's temperature records when they arrive and the disposition of the product. A file that is complete on day one is far easier to defend on day sixty.
A hypothetical example worked through
Consider a hypothetical dairy shipper and the 6:20 a.m. load. Twenty pallets were loaded. The quality manager reviews the probe readings by phone and approves receiving the front 14 pallets and rejecting the rear 6. The receiver notes the split on the delivery receipt with the temperatures. The driver photographs the unit, which shows the setpoint at 36°F but a return air of 47°F.
The coordinator emails the carrier at 8:00 a.m. with the facts and a request for the unit download. The 6 rejected pallets, worth a hypothetical $11,400 at invoice value, go to a local cold storage facility while the carrier decides whether to inspect. A replacement of 6 pallets ships that afternoon. Two days later, the download shows a defrost cycle stuck for five hours during the night. The claim file now has the instruction in writing, the product temperatures at both ends and the carrier's own record of the failure.
How does a temperature claim work after the first day?
A temperature claim is a cargo loss and damage claim: the claimant files it in writing with the carrier, within the time limits in the bill of lading or contract, with enough facts to identify the shipment, a statement of liability and a specified amount. Federal rules then set how the carrier must respond.
What a valid claim must contain
Under 49 CFR 370.3, a written claim must contain facts sufficient to identify the shipment, assert liability for the loss or damage and claim a specified or determinable amount of money. A claim missing any of these can be returned as incomplete. "Product arrived warm, please advise" is a notice, not a claim.
Filing deadlines
For interstate shipments, 49 U.S.C. 14706 says a carrier may not set a period shorter than nine months to file a claim or shorter than two years from a written denial to bring a lawsuit. Contracts and tariffs may set exact terms within those limits, so check the carrier agreement. In practice, file as soon as the file is complete: memories fade and records get overwritten.
How the carrier must respond
Under 49 CFR 370.5, the carrier must acknowledge a claim in writing within 30 days of receiving it, unless it has paid or declined it within that time. Under 49 CFR 370.9, the carrier must pay, decline or make a firm settlement offer within 120 days. If it cannot, it must tell the claimant in writing why, and repeat that update every 60 days while the claim is open.
What determines the amount
Most claims are based on the value of the lost or damaged product, minus any salvage recovered. The carrier's agreement or tariff may limit liability, so check it before filing. Freight charges for the damaged portion are often part of the conversation. Replacement freight and other costs may or may not be recoverable, depending on the terms and the facts. Keep each cost separate on the file so the claim can be adjusted without rebuilding it.
What the carrier will look at
The carrier will compare the instructions with what happened. It will check that the setpoint and mode on the BOL and rate confirmation match the unit's settings. It will check product temperatures at loading. It will look for gaps in its own data: shutdowns, door openings, defrost cycles and alarms. It will look at the time the truck waited at either dock. A claim that answers those questions up front moves faster. The general process is covered in how to file a freight damage claim.
Claim file contents and why each matters
| Document or record | What it proves | When to collect it |
|---|---|---|
| BOL with setpoint and mode | The instruction was given in writing | At booking and loading |
| Rate confirmation with the same instruction | The carrier agreed to it | At booking |
| Product temperatures at loading | The product left in range | At loading |
| Photo of unit display at loading | The trailer was pre-cooled and set correctly | At loading |
| Delivery receipt with exception notes | The problem was found at delivery, not later | At delivery |
| Product probe readings at delivery | Which product was affected and how badly | At delivery |
| Photos at delivery | Condition, positions and unit display | At delivery |
| Carrier's unit download | What the unit actually did during the trip | Same day, by request |
| Written notice to the carrier | The carrier was told and could inspect | Same day |
| Disposition record | What happened to the product and any salvage value | As it happens |
| Invoice value of the product | The amount of the loss | When filing |
What are the most common root causes, and how do you fix them?
Most out-of-temperature loads come from one of five causes: warm product at loading, a wrong setpoint or mode, a unit failure, a long wait with doors open or a trailer that was never pre-cooled. The carrier's record and the loading records usually show which one, and each has its own fix.
Warm product at loading
If the product was already above range when it was loaded, the reefer unit could not bring it down: reefers hold temperature, they do not chill product quickly. The fix is a rule to probe product before loading and to hold any pallet that is above range. In this case, the claim against the carrier is weak, and the cause sits at the shipper's own dock.
Wrong setpoint or mode
A setpoint written as "36" without the unit, a phone instruction that never reached the paperwork or a unit left on cycle mode when the product needed continuous airflow will all show up in the download. The fix is to write setpoint, unit and mode on the quote request, the rate confirmation and the BOL, every time, and to check the unit display at loading.
Unit failure in transit
A stuck defrost cycle, a refrigeration failure or a fuel outage shows in the carrier's records as a gap or a temperature climb. This is the clearest carrier liability case. The fix for future loads is to ask, after the claim, how the carrier monitors its units and what alarm process it follows.
Long waits at the dock
A truck that waits hours at a receiver, or opens its doors repeatedly for a multi-stop delivery, can warm up even with a working unit. Check arrival and unloading times. If the receiver kept the truck waiting, the cause may sit with the receiver, not the carrier.
No pre-cooling
A trailer loaded warm takes time to cool the air, and product near the doors can warm in the meantime. The federal rule says a carrier offering refrigerated equipment for food must pre-cool it as the shipper specifies, so specify pre-cooling in writing and check the unit display before the first pallet goes on.
Root cause decision table
| What the records show | Likely cause | Who should fix it | Next step on the lane |
|---|---|---|---|
| Product warm at loading, unit steady | Warm product | Shipper's warehouse | Probe before loading; hold warm pallets |
| Unit set to a different setpoint or mode | Instruction error | Shipper or carrier, depending on paperwork | Put setpoint, unit and mode on every document |
| Unit record shows failure or shutdown | Equipment | Carrier | File claim; review the carrier on the lane |
| Long dwell at receiver, doors open | Delivery conditions | Receiver and shipper | Tighten appointments; review multi-stop plans |
| Trailer warm at loading start | No pre-cooling | Carrier | Specify pre-cooling in writing; check before loading |
| Records missing or incomplete | Unknown | Both | Require unit downloads on request as a booking term |
Mistakes that weaken the claim
Signing clean. A receipt signed without notes suggests the product arrived fine.
Discarding product too fast. If the carrier never had a chance to inspect, it may dispute the amount.
Probing only one pallet. One reading can't show how much of the load was affected.
Waiting to ask for the unit record. Data and memories are easier to retrieve in the first days.
Mixing claim costs. Product value, freight, replacement freight and disposal should be listed separately.
Which checklist should the receiver, logistics and quality share?
A shared response checklist turns a 6 a.m. phone call into a sequence everyone already knows. Send it to the customers that receive reefer freight and keep it on file for the team.
| When | Action | Owner |
|---|---|---|
| At the dock | Probe product front, middle and rear, top and bottom; record by pallet | Receiver |
| At the dock | Photograph the unit display, probes, pallet positions and condition | Receiver or driver |
| At the dock | Write exceptions and temperatures on the delivery receipt before signing | Receiver |
| At the dock | Set affected product aside in a cold area | Receiver |
| First hour | Decide accept, partial accept or reject based on product limits | Quality owner with the receiver |
| First hour | Ask the driver for the unit's settings and trip history | Logistics |
| Same day | Send the carrier a written notice and offer inspection | Logistics |
| Same day | Request the unit download for the trip in writing | Logistics |
| Same day | Arrange replacement product for the customer | Customer service and logistics |
| First week | Record what happened to the rejected product and any salvage | Logistics |
| First week | File the written claim with the amount and evidence | Logistics or claims owner |
| After 30 days | Confirm the carrier acknowledged the claim | Claims owner |
| Ongoing | Identify the root cause and change the lane rules if needed | Logistics and quality |
How to put it in place
Start with the customers and lanes that carry the most temperature-sensitive product. Agree on the quality contact who can approve a rejection, and give receivers a phone number and an email that someone answers early in the morning. Review the checklist after every incident: if a step was skipped, find out why, and adjust the order or the owner.
How does Wilson, by Cartage, handle a reefer load that arrives out of temperature?
Wilson, by Cartage, is an AI logistics agent that quotes, books, tracks, audits and pays freight for manufacturers and distributors, and it runs the claims workflow the company defines during onboarding. Traditional logistics software gives teams information. Wilson executes the work required to move shipments forward.
Wilson works as the company's free logistics department, built from four parts.
The labor
The labor is the work from the first quote to the final POD. Wilson books reefer loads with the instructions the company sets, writing them on the rate confirmation and generating the bill of lading. When a load arrives out of temperature, Wilson asks the receiver for photos and to set the product aside, opens the claim with the carrier and tells the team what it did. It can request, chase and file the documents configured in the workflow, such as the carrier's temperature record for the trip, and it follows up with the carrier by phone and email until it gets an answer. Wilson usually talks to the carrier's dispatch and can call or text the driver when it has the driver's number. If a replacement shipment is needed, Wilson can quote and book it with the company's approved carriers within the rules or after approval, and tell the customer if configured. Decisions on product safety and acceptance stay with the company's people.
The data
The data is the record. Wilson keeps every order, load, quote, rate, document and contact on record as it works. The BOL, the rate confirmation, the photos, the carrier's notice, the temperature records and every message about the claim sit on the same shipment, with each change kept in the shipment's change history. Wilson replaces the TMS for freight execution and connects to the company's ERP. Wilson works with SAP, NetSuite, Microsoft Dynamics 365, Oracle, Infor, Epicor, Sage, Acumatica and other ERP environments, with the exact connection depending on the customer's data flow and scope.
The network
The network gives the shipper better freight rates on every lane, including reefer lanes, because its volume counts with every other Wilson customer's. The network includes carriers and brokers, and the company still approves who hauls its freight.
The payments
The payments keep the money tied to the evidence. Wilson audits each carrier invoice against the rate confirmation and the POD before paying. Invoices outside the rules wait for a person, and the whole invoice waits, since there are no partial payments. How the freight invoice for a load with an open claim is handled is part of the claims process the company defines during onboarding. Approved invoices are paid from the Wilson Wallet.
Control starts with assisted execution. The company sets approval limits, and routine actions can run automatically within those rules as the workflow is proven. Timing depends on scope: most teams start on a few lanes and expand from there. For how delivery records reach the claim and the invoice, see POD collection for food shipments.
Pricing
Wilson is free on Wilson's network: the shipper pays the freight rate and nothing on top. When a shipper keeps its own carriers, the fee is 2% to 0.5% of what Wilson pays them, falling with volume. There are no seat fees, no setup cost and no contract.
FAQs
What does Wilson do when a reefer load arrives out of temperature?
Wilson, by Cartage, an AI logistics agent, follows the claims process the company defines during onboarding. It asks the receiver for photos and to set the product aside, opens the claim with the carrier and tells the team what it did. Every document and message is kept on the shipment, and decisions on product safety stay with the company.
Should the receiver reject the whole load?
Not automatically. Probe product at several points and decide by pallet. Often part of the load is in range and can be received, while the affected pallets are rejected. Record exactly which pallets were accepted and which were not.
Can we throw away the warm product right away?
Wait until the carrier has been notified and has had the chance to inspect, unless safety rules require faster disposal. Record what was done with the product and any salvage value. Disposal without notice can weaken the claim.
Does the carrier have to show its temperature records?
For food, under the federal sanitary transportation rule, a carrier that has agreed in writing to be responsible for temperature control must, on request, show that it held the temperature the shipper specified. The parties can agree on how, such as readings at loading and unloading or trip temperature data. Ask for the records in writing the same day.
How long do we have to file a temperature claim?
For interstate shipments, carriers can't require claims to be filed in less than nine months, or lawsuits in less than two years from a written denial. The carrier agreement may set exact terms within those limits. File as soon as the claim file is complete.
What must a written claim include?
Facts that identify the shipment, a statement that the carrier is liable and a specified or determinable amount of money. A message saying the product arrived warm is a notice, not a claim. Attach the evidence so the carrier can investigate.
How fast must the carrier respond to a claim?
The carrier must acknowledge a claim in writing within 30 days, unless it pays or declines it first. It must pay, decline or make a firm offer within 120 days, or explain the delay in writing and update the claimant every 60 days.
What if the product was warm when it was loaded?
Then the claim against the carrier is weak, because reefer units hold temperature rather than cool warm product quickly. Fix the cause at the shipping dock: probe product before loading and hold anything above range.
Does Wilson monitor the reefer unit's temperature during transit?
Wilson tracks loads with the best source available for each one, such as carrier APIs, EDI, GPS or ELD data the carrier shares, the carrier's website or calls and emails. Whether trip temperature data can be included depends on what the carrier shares and the setup, so confirm it in discovery. Wilson can request the carrier's temperature record as a document in the workflow.
Who should be told when a reefer load fails?
The carrier in writing, the person who owns product quality, the logistics team, finance for the claim and the customer, who still needs product. Agree in advance who calls whom so the first hour is not spent finding phone numbers.
Sources
- 21 CFR 1.908, Requirements applicable to the sanitary transportation of human and animal food: https://www.law.cornell.edu/cfr/text/21/1.908
- 49 CFR 370.3, 370.5 and 370.9, Filing, acknowledgment and disposition of loss and damage claims: https://www.law.cornell.edu/cfr/text/49/part-370
- 49 U.S.C. 14706, Liability of carriers under receipts and bills of lading: https://www.law.cornell.edu/uscode/text/49/14706
- Cartage, Wilson product FAQ and product scope, October 2026: https://cartage.ai
Let's review how your team handles a temperature claim today. You don't need to prepare anything: Cartage maps the workflow with you on the call.
