How do we ship heavy loads like beverages without going over truck weight limits?

Bills of lading guideNov 16, 202617 min read

How do we ship heavy loads like beverages without going over truck weight limits?

Consider a hypothetical beverage bottler. A distributor orders 24 pallets of canned sparkling water for one delivery. Each pallet weighs about 2,300 pounds. The order team sees 24 pallets and books a 53-foot dry van, because 24 pallets is a normal truckload count. At 55,200 pounds of product, the load is far over what any standard tractor and trailer can legally carry. The driver arrives, the shipping lead does the math on the dock, and the truck leaves with 18 pallets. Six pallets sit on the floor, the customer gets a short delivery and someone has to book another truck.

To ship heavy loads without going over weight limits, plan each load by weight first and floor space second: know the carrier's maximum payload for the equipment, build each load to stay under it with the weight spread evenly over the axles, and put accurate weights on the order, the quote request and the BOL. Heavy freight runs out of weight capacity long before it runs out of room, so a pallet count alone says almost nothing about whether a load is legal.

What the federal limits say

The Federal Highway Administration summarizes the federal standards for commercial vehicles on the Interstate Highway System:

  • Gross vehicle weight: 80,000 pounds.
  • Single axle: 20,000 pounds.
  • Tandem axle: 34,000 pounds.
  • Bridge formula: adopted in 1975 to protect bridges, it may require a lower gross weight depending on the number and spacing of the axles.

Off the Interstate, states set their own weight standards. Federal law also includes exemptions and variations for particular states, routes, vehicles and operations, including grandfathered limits in some states. That means the legal answer for a specific route can differ from the headline numbers. The carrier is the party that knows its equipment and routes, so treat the federal numbers as the frame and the carrier's stated payload as the working limit.

Why the truck's own weight matters

The 80,000 pounds covers everything: tractor, trailer, fuel, driver and freight. The tractor and trailer take a large share of that before a single pallet is loaded. A carrier running a lighter tractor or trailer can legally haul more product than one running heavier equipment. That is why two carriers on the same lane can give different maximum payloads, and why "a full truckload" means a different number of pallets for heavy freight than for light freight.

Weigh out versus cube out

A load weighs out when it reaches the weight limit before the trailer is full. It cubes out when it fills the trailer's space before reaching the weight limit. Beverages, canned food, bagged ingredients, paper rolls, tile, metal parts and most liquids weigh out. A trailer of canned drinks at its legal limit often has open floor space, sometimes a lot of it. That empty floor is normal and legal. Trying to fill it is how loads end up overweight.

Let's review your heaviest lanes and how loads are built. You don't need to prepare anything: Cartage maps the workflow with you on the call.

See it on your own loads. Wilson, by Cartage, is an AI logistics agent that quotes, books, tracks, audits and pays for freight with your approved carriers.

Book a demo →

Build heavy loads from the carrier's payload down, not from the pallet count up, and spread the weight so no axle group carries more than its share. The steps below turn that into a routine the dock can follow every time.

Step 1: Get the real weight of each pallet

Use actual pallet weights, not catalog estimates. For products that ship in the same pallet configuration often, weigh a standard pallet once, including the pallet, slip sheets and wrap, and store the number for that SKU and configuration. For mixed pallets, add up the case weights from the item master and add the pallet and packaging. A stored weight that is off by 50 pounds per pallet adds up to more than a thousand pounds on a full load.

Step 2: Ask the carrier for its maximum payload

Before building the load, ask the carrier what it can legally haul on that lane with the equipment it plans to send. Write the answer on the quote and the booking. If several carriers quote the lane, record each one's payload, because a carrier with a higher payload may move the same order on fewer trucks.

Step 3: Set the pallet count from weight

Divide the payload by the pallet weight and round down. With a hypothetical payload of 43,000 pounds and 2,300-pound pallets, the load is 18 pallets, at 41,400 pounds. That leaves margin for variation in pallet weight. Do not plan to the last pound: scales differ, pallets vary and a load built exactly to the limit leaves no room for error.

Step 4: Spread the weight along the trailer

Axle limits apply to each axle group. If all the heavy pallets sit at the front of the trailer, the drive axles carry too much even when the gross weight is fine. If they all sit at the back, the trailer axles do. For weigh-out loads with open floor, load pallets in a pattern the carrier approves, usually spread along the trailer rather than bunched at one end. Some carriers prefer a single row down the center or alternating positions. Ask.

Step 5: Let the driver adjust and scale

Drivers can often shift weight between axle groups by moving the trailer's tandem axles or the tractor's fifth wheel. After loading, many drivers weigh the truck at a nearby certified scale. If an axle group is over, a small adjustment may fix it. If the gross weight is over, freight has to come off. Agree in advance where the driver will scale and who calls whom if the truck is over.

Step 6: Record the weights on the paperwork

The BOL should show the number of pallets and the weight that actually shipped. If the load changed at the dock, update the BOL before the driver leaves. The guide on whether the BOL still matches when the pallet count changes covers what to fix and who signs.

A worked load plan

The table below shows one hypothetical order split across trucks. It shows the method, not a legal limit for any specific equipment.

Item Value
Order 24 pallets canned sparkling water
Weight per pallet (stored, weighed) 2,300 lb
Order weight 55,200 lb
Carrier's stated maximum payload 43,000 lb (hypothetical)
Pallets per truck by weight 18 (41,400 lb)
Trucks needed 2
Better split 12 pallets per truck (27,600 lb each), or 18 + 6 with the 6 combined with another order to the same area

The "better split" line is where money is made or lost. Two half-full trucks may cost more than one full truck plus a smaller shipment, or less, depending on the lane. Quote both ways.

How do heavy loads change quoting, modes and cost?

Heavy freight changes how carriers price it and which mode makes sense. The shipper pays for weight in a way light freight never triggers, so the quote request needs different details.

What a heavy-freight quote request needs

Send carriers the information they need to decide whether they can legally haul the load:

  • Total weight and weight per pallet.
  • Pallet count, dimensions and whether pallets can be stacked (stacking heavy pallets is often not possible or not wise).
  • Commodity, and whether it is liquid, which can shift in transit.
  • Pickup and delivery locations, so the carrier can check the route.
  • Any delivery restrictions, such as a site that cannot take a full-weight truck.

A request without the weight invites a quote for a load the carrier cannot actually take. That quote is worthless, and finding out at the dock costs a day.

Truckload: price per load, payload per carrier

In truckload, the carrier charges for the trailer. Heavy freight usually does not raise the per-load rate the way it would in LTL, but it limits how much product each load carries. So the useful comparison is cost per pallet or cost per pound shipped, not cost per load. A carrier with a slightly higher rate and a higher payload can be cheaper per pallet.

Carrier (hypothetical) Rate per load Stated payload Pallets per load at 2,300 lb Cost per pallet
Carrier A $2,100 42,000 lb 18 $116.67
Carrier B $2,250 45,000 lb 19 $118.42
Carrier C $2,300 46,500 lb 20 $115.00

Carrier A has the lowest rate per load. Carrier C moves the most product per truck at the lowest cost per pallet, so on a large order or a program of repeat loads it can need fewer trucks and cost less overall. The right answer depends on order sizes, not just the headline rate.

LTL: dense freight prices well but gets reweighed

Dense freight usually falls into lower LTL freight classes, which keeps the rate per hundred pounds down. But LTL carriers reweigh freight at their terminals, and heavy shipments are exactly where a wrong declared weight shows up. A pallet declared at 1,800 pounds that weighs 2,300 pounds will be billed at the real weight, often with a reweigh charge. Declared weights should come from the scale or the stored standard, not an estimate.

Splitting and combining orders

Large heavy orders often need more than one truck. Before splitting, check:

  • Whether the customer prefers several full deliveries or one large delivery with a partial truck.
  • Whether part of the order can be combined with another order going to the same area.
  • Whether the remaining pallets fit an LTL or volume LTL shipment at a lower cost than a second truck.

When the load is overweight at the dock

If the truck is over, someone has to decide which pallets come off, where they go and how they ship. That decision costs driver time, and long waits can lead to detention charges. If the order was never going to fit, the carrier may also charge for a truck that showed up and could not load as planned. The guide on avoiding truck-ordered-not-used and dry-run charges covers how those charges work.

What mistakes cause overweight loads and extra charges?

Most overweight problems start at order entry, not at the dock. The truck arrives with a load plan that was wrong before anyone touched a pallet.

Mistake 1: Booking by pallet count

A 53-foot trailer holds many more pallet positions than a heavy load can use. Booking "one truckload" for an order that weighs 55,000 pounds guarantees a problem. Book by weight.

Mistake 2: Using catalog weights

Catalog weights often leave out the pallet, slip sheets, wrap and the extra cases a dock team adds to fill a layer. For heavy freight, those pounds matter. Weigh a standard pallet and store it.

Mistake 3: Planning to the last pound

A load built to exactly the carrier's payload has no margin. Pallet weights vary, fuel tanks vary and scales differ. Leave room.

Mistake 4: Assuming every carrier has the same payload

Equipment differs. A load that one carrier can haul may be too heavy for another. Ask, and record the answer on the booking.

Mistake 5: Ignoring weight distribution

A legal gross weight does not mean legal axle weights. Bunching heavy pallets at the nose or the tail overloads one axle group. Follow the carrier's loading pattern.

Mistake 6: Changing the load without changing the paperwork

When pallets come off at the dock, the BOL often still shows the original count and weight. The receiver then sees a shortage, the invoice may not match and nobody knows where the missing pallets are. The guide on what happens when a driver changes the BOL pallet count at pickup walks through the follow-up.

Mistake 7: Not telling the customer

If an order splits across two trucks or ships short, the customer's receiving team needs to know before the first truck arrives, not after.

Decision rules for heavy orders

Situation Rule
Order weight above one carrier's payload Split by weight before booking; quote both splits
Pallet weight not stored Weigh one before quoting
Carriers give different payloads Compare on cost per pallet, not per load
Remaining pallets after a full truck Quote LTL or volume LTL against a second truck
Truck over at the scale Shift axles first if only an axle group is over; remove freight if gross is over
Pallets removed at the dock Update the BOL, tell the customer, book the remainder
Invoice shows a reweigh Compare the reweigh with the BOL and stored weights before paying

A short checklist at order entry, at booking and at the dock catches most heavy-load problems before they cost money.

Stage Check Owner
Order entry Is the order's total weight known, from stored pallet weights? Order owner
Order entry Is the order heavier than one truck's typical payload? Logistics
Quoting Does the quote request show total weight, pallet weight and count? Logistics
Quoting Did each carrier state its maximum payload for the equipment? Logistics
Quoting Were quotes compared on cost per pallet as well as per load? Logistics
Booking Does the rate confirmation show the weight and pallet count? Logistics
Booking Does the customer know if the order ships on more than one truck? Order owner
Loading Is the load pattern the one the carrier asked for? Shipping
Loading Where will the driver scale, and who is called if it is over? Shipping
Departure Does the BOL show what actually shipped? Shipping
Invoice Do the billed weight and charges match the booking and BOL? Finance or logistics

Keep a payload list per carrier and lane

Over time, record each carrier's stated payload by lane and equipment. That list lets the team plan loads before quoting and spot carriers that consistently move more product per truck. Review it when a carrier changes equipment.

Watch the reweigh and short-shipment patterns

Once a month, count the loads that were reworked at the dock, shipped short or reweighed on the invoice. A cluster on one product means its stored weight is wrong. A cluster on one carrier means its stated payload does not match what its trucks actually carry. A cluster at one plant means the dock process needs work.

Share the load plan with the dock

The best load plan is useless if the dock never sees it. Send the planned pallet count and weight per truck with the pick list, so the dock builds the right load the first time.

How does Wilson, by Cartage, help ship heavy freight within weight limits?

Wilson, by Cartage, is an AI logistics agent that quotes, books, tracks, audits and pays freight for manufacturers and distributors, and it makes sure every heavy load is quoted and documented with real weights. Traditional logistics software gives teams information. Wilson executes the work required to move shipments forward.

Wilson does not plan loads, calculate axle weights or decide whether a truck is legal on a route. Load building stays with the dock and the carrier stays responsible for its equipment. What Wilson does is make sure the weight information moves correctly from order to quote to BOL to invoice, so the truck that shows up can take the load. Cartage describes Wilson as a free logistics department in four parts.

The labor

The labor covers the work from the first quote to the final POD. When an order arrives by email, an ERP connection or a CSV or XLSX file, Wilson checks it for the details a quote needs. If the weight is missing, Wilson does not book it: it holds the order as pending, asks for the missing detail and tells the team. It never invents the missing value. Wilson then requests quotes from the company's approved carriers with the weight and pallet count on the request, compares them on total cost, negotiates toward the company's rate targets within approval limits and books with written acceptance and a rate confirmation. It generates the BOL, packing slips and pallet labels, schedules the pickup, tracks the load and follows up with carriers by phone and email until it gets an answer. Wilson checks carrier availability before booking; if a carrier can only pick up later, Wilson presents that to the team and leaves the agreed date for the team to change.

The data

The data is the record of every order, load, quote, rate, document and contact, connected to the company's ERP. The team can keep rules and notes Wilson follows, such as "this lane ships at most 18 pallets per truck" or "this plant's dock loads heavy pallets in a single row," and edit them at any time. If the team changes something on one load, Wilson treats it as a change to that load and asks whether it should become a rule. Wilson replaces the TMS for freight execution and connects to the company's ERP. Every message, confirmation and change is kept in the shipment's change history.

The network

The network gives better freight rates on every lane, because the shipper's volume counts with every other Wilson customer's. The network includes carriers and brokers. The company still approves who hauls its freight.

The payments

The payments protect the money. When a BOL changes after pickup, for example a new pallet count, weight, address or freight class, the change is routed to the load owner. Wilson audits each carrier invoice against the rate confirmation and POD, and checks reweigh and reclass lines against the booking and the documents. An invoice over the rate is flagged, and Wilson asks the carrier why before paying. Carriers are paid from the Wilson Wallet, and payments above the approval limits or outside the rules wait for a person.

Wilson works with SAP, NetSuite, Microsoft Dynamics 365, Oracle, Infor, Epicor, Sage, Acumatica and other ERP environments, with the exact connection depending on the customer's data flow and scope. Control starts with assisted execution: the company sets approval limits, and routine actions run automatically within those rules as the workflow is proven. Timing depends on scope: most teams start on a few lanes and expand from there.

Pricing

Wilson is free on Wilson's network: the shipper pays the freight rate and nothing on top. When a shipper keeps its own carriers, the fee is 2% to 0.5% of what Wilson pays them, falling with volume. There are no seat fees, no setup cost and no contract.

FAQs

Can Wilson keep our heavy loads within weight limits?

Wilson, by Cartage, an AI logistics agent, makes sure every load is quoted and documented with its real weight: it will not book an order missing its weight, puts the weight and pallet count on every quote request and BOL and routes BOL changes to the load owner. It does not calculate axle weights or decide route legality. Load building stays with the dock, and the carrier remains responsible for its equipment.

What is the federal truck weight limit?

On the Interstate Highway System, the federal limits are 80,000 pounds gross vehicle weight, 20,000 pounds on a single axle and 34,000 pounds on a tandem axle. The bridge formula can require a lower gross weight depending on the number and spacing of axles. Off the Interstate, states set their own standards.

How much product can a truck carry?

It depends on the tractor, trailer and fuel, because their weight comes out of the gross limit. Ask each carrier for its maximum payload on the lane and equipment, and plan below it.

Why does a full trailer of beverages leave empty floor space?

Because beverages weigh out: they reach the weight limit before they fill the trailer. Empty floor space on a heavy load is normal and is not a sign the load is underused.

What happens if a truck is overweight at the scale?

If only an axle group is over, the driver may be able to shift weight by moving the trailer axles or the fifth wheel. If the gross weight is over, freight has to come off, which costs time and may lead to extra charges.

How should we compare truckload quotes for heavy freight?

Compare cost per pallet or per pound shipped, not just the rate per load. A carrier with a higher payload can move more product per truck and cost less per pallet.

Why do LTL carriers reweigh heavy shipments?

Carriers check declared weights at their terminals. When the real weight is higher than the BOL, they bill the real weight and may add a reweigh charge. Accurate stored pallet weights prevent it.

What should happen to the BOL when pallets come off at the dock?

Update it before the driver leaves so it shows what actually shipped, tell the customer and book the remaining pallets. A BOL that still shows the original count causes shortage claims and invoice mismatches.

Does Wilson check reweigh charges before paying?

Yes. Wilson audits each invoice against the rate confirmation and POD, and checks reweigh lines against the booking and the documents. Invoices outside the rules wait for a person.

Sources

Let's review your heaviest lanes and how loads are built. You don't need to prepare anything: Cartage maps the workflow with you on the call.

Add Cartage as a preferred source on Google